• <div id="qw8ga"><li id="qw8ga"></li></div>
  • Welcome to shandong drick instruments co.,ltd

    Products

    Plastic soft package testing instrument
    Location:Index ? Rubber testing machine ? DRK208 Melt Flow Rate Tester
    DRK208 Melt Flow Rate Tester

    DRK208 Melt Flow Rate Tester

    Product brand:  DRICK
    Detection project:  Melt Flow Rate Testing
    Product video:  
    Product documentation:  
    Product enquiry:  
    Counseling hotline:0531-85868997  0531-85760992

    DRK208Melt Flow Rate Tester is used for measuring melt flow rate of polyethylene, polypropylene, polyformaldehyde, ABS resin, polycarbonate, nylon fluoroplastic and other polymers at high temperature according to the test method of GB3682-2018. It is suitable for production and research in factories, enterprises and scientific research institutes.


    Product details

    Main characteristics:

    1、Extrude the discharge part

    Discharge port diameter: φ 2.095±0.005 mm

    Discharge port length: 8.000±0.005 mm

    Diameter of charging barrel: φ 9.550±0.005 mm

    Length of charging barrel: 160±0.1 mm

    Piston rod head diameter: 9.475±0.005 mm

    Length of piston rod head: 6.350±0.100 mm

    2、Standard test Force (Grade 8)

    Grade 1:0.325kg = (piston rod + weight tray + heat insulation sleeve + no. 1 weight body)

    = 3.187 N

    Grade 2:1.200kg =(0.325+ No.2 0.875 weight)= 11.77N

    Grade 3:2.160kg =(0.325+ No.3 1.835 weight)= 21.18N

    Grade 4:3.800 kg=(0.325+ no.4 3.475 weight)= 37.26N

    Grade 5:5.000 kg=(0.325+ no.5 4.675 weight)= 49.03N

    Grade 6:10.000 kg=(0.325+ No.5 4.675 weight + No.6 5.000 weight)= 98.07N

    Grade 7:12.000 kg=(0.325+ no.5 4.675 weight + No.6 5.000+ No.7 2.500 weight)= 122.58N

    Grade 8:21.600 kg=(0.325+ number 2 0.875 weight + Number 3 1.835+ Number 4

    3.475+5 4.675+6 5.000+7 2.500+8 2.915 weight)= 211.82N

    Relative error of weight 0.5%.

    3、Temperature range50-300

    4、Constant temperature precision:±0.5℃。

    5、Power supply220V±10%    50Hz

    6、Working environment: ambient temperature is 10-40; The relative humidity of the environment is 30%-80%; No corrosive medium around, no strong air convection; There is no vibration and strong magnetic field interference around.

    7、Instrument dimensions250×350×600=L×W×H

    Structure and working principle:

    Melt flow rate meter is an extruded plastic meter. It is in the specified temperature conditions, with high temperature heating furnace to make the measured material to achieve melting state. The molten state of the measured material, under the specified weight load gravity through a certain diameter of the hole extrusion test. In the plastics production of industrial enterprises and the research of scientific research institutes, "melt (mass) flow rate" is often used to express the fluidity, viscosity and other physical properties of polymer materials in the melting state. The so-called melting index refers to the average weight of each section of the sample extruded into 10 minutes of extrusion.

    Melt (mass) flow rate meter is expressed by MFR, the unit is: g/ 10 min (g/min) Formula: MFR(θ, mnom)                       =tref  .m/t

    In the formula θ——  Test temperature

              mnom—  Nominal load Kg

               m ——  The average mass of the cut g

              tref ——  Reference time10min, S ( 600s )

               t  ——  Time interval for cutting s

    The instrument is composed of heating furnace and temperature control system and installed on the fuselage (column) base.

    The temperature control part adopts single-chip microcomputer to adjust the power and control the temperature, which has strong anti-interference ability, high temperature control precision and stable control. The heating wire in the furnace is wound on the heating rod according to a certain law to minimize the temperature gradient and meet the standard requirements.

    Matters needing attention:

    1、Single power socket must have grounding wire hole, and reliable grounding.

    2、If there is abnormal display on the LCD, it should be shut down first, and then reset the test temperature and start the work.

    3、In normal operation, if the furnace temperature is more than 300, software protection, heating interruption, and alarm.

    4、If there are abnormal phenomena, such as temperature control, can not display, etc., should be shut down for maintenance,

    5、When cleaning the piston rod, do not scrape with hard objects. 


    About Drick
    Company profile
    Organization
    Development event
    Honor
    Product Center
    leather&footwear industry
    Rubber testing machine
    Leather testing machine
    Fabric testing machine
    Analytical instruments
    Medical mask protective & clothing testing instruments
    Paper and packaging testing instruments
    Plastic flexible packaging testing instruments
    Printed materials testing instruments
    Industrial testing equipment
    Assistive devices
    Imported testing equipment
    News and information
    Common problem
    Industry information
    Company news
    Application industry
    Paper and Packaging Industry
    Food industry
    Pharmaceutical industry
    Quality inspection
    Scientific research
    Medical apparatus and instruments
    Detection service
    Laboratory introduction

    Copyright 2013@Shandong Drick Instruments Co., Ltd. Record number: Lu ICP 12028852 Excellent provider of packaging testing equipment and testing services.

    X whatsapp:
    Ms Charlene: 008613370587908
    Ms Alice: 008613573193157
    Ms Wendy: 008615806605792
    日韩精品亚洲国产一区蜜芽